Temperature Controllers www.tempco.com | (800) 323-6859 | email: [email protected] 13-60 Part Number TEC99927 — Converter Connects RS232/RS422/RS485 Devices To PC Via USB Port Part Number TEC99928 — Converter Connects RS422/RS485 Devices To PC Via USB Port Specifications TEC99927 USB Version: 900/1800 MHz, dual band Connector: USB type B Speed: 12 Mbps Serial Interface Number of Ports: 1 RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: T×D+(B), T×D-(A), R×D+(B), R×D-(A),GND RS-485: 4-wire: T×D+(B), T×D-(A), R×D+(B), R×D-(A), GND 2-wire: Data+(B), Data-(A), GND Connector: Male DB9 FIFO: 64 bytes Serial Line Protection: 15 KV ESD for all signals Serial Communications Parameters Parity: None, Even, Odd, Space, Mark Data Bits: 5, 6, 7, 8 Stop Bits: 1, 1.5, 2 Flow Control: RTS/CTS, XON/XOFF Speed: 50 bps to 921.6 Kbps Power Requirements Power Consumption: 30 mA@5 VDC Mechanical Dimensions: 37.5 × 20.5 × 60 mm (L × W × H) Specifications TEC99928 Chipset: Silicon Laboratories CP2102 Compliant: USB 1.0, 1.1, 2.0 Connector: USB type A Baud Rates: Full Speed 12 Mbps Part Number TEC99927 TEC99003 Smart Network Adapter TEC Control Port Cable Programming Port Cables TEC99011 — Used for models TEC-220, TEC-4100, TEC-7100, TEC-8100 and TEC-9100. TEC99012 — Used for model TEC-920 only. TEC99013 — Used for models TEC-2500, TEC-4300, TEC-8300 and TEC-9300. TEC99014 — RS-232 interface cable for models TEC-220, TEC-410, TEC-2500, TEC-4100, TEC-4300, TEC-4500, TEC-8100, TEC-8300, TEC-9100, TEC-9300, TEC-9500 and TBC-41. TEC99001 — Smart Network Adapter for third party SCADA software which converts 255 channels of RS-485 or RS-422 to RS-232 Network. TEC99003 — Smart Network Adapter for connecting the TEC controller’s programming port to the RS-232 PC serial port. Allows downloading and reading of configuration information directly from a personal computer. Can be used with TEC-220, TEC-410, TEC-910, TEC-920, TEC-2500, TEC-4100, TEC-4300, TEC-4500, TEC-7100, TEC-8100, TEC-8300, TEC-9100, TEC-9300, TEC-9500 and TBC-41. TEC99030 — "Tempco Config Set" PC software for use with TEC99003 Smart Network Adapter Minimum System Requirements: Microsoft Windows XP, 2000, NT, 98, 95 Pentium 200 MHz or faster 32 MB RAM (64 MB recommended) Hard disk space: 2 MB Note: Can be downloaded at no charge from www.tempco.com Data Communication Accessories Temperature Control Design Features ✴ Ideal for interfacing with TEC controllers, PPR chart recorders, PLCs, and general protocol conversion to a USB port ✴ Full-Speed USB operation at up to 12 Mbps ✴ Additional I/O or IRQ not required ✴ Serial transmission speed up to 921.6 Kbps ✴ 64-byte FIFO and built-in hardware and software flow control ✴ Built-in 15 KV ESD protection ✴ Support for RS-232, RS-422, 2-wire RS-485, and 4-wire RS-485 ✴ Terminal block adapter Part Number TEC99928
