Temperature Controllers www.tempco.com | (800) 323-6859 | email: [email protected] 13-32 Model TEC-4500 1/4 DIN & Model TEC-9500 1/16 DIN Ramp & Soak Temperature Controls Design Features ✴ Ramp & Soak Programmable Control ✴ Nine recipes (profiles) available using 64 segments maximum per recipe ✴ Event Input – one of 8 functions can be chosen: start run mode, hold mode, abort recipe, manual mode, failure transfer, turn off, segment advance, select 2nd set of PID parameters ✴ Event Output – 3 relays are available. Can be programmed to any segment or end of recipe ✴ Analog Retransmission – optional mA or VDC transfer of PV or SV values ✴ Highly accurate universal input with 18 bit analog to digital converter ✴ Bright 0.40" (10mm) red LED process display ✴ Fast sample rate – 200ms ✴ Fuzzy Logic PID Autotune heat and cool control – 2 sets of values can be used ✴ Optional RS-485 or RS-232 communications interface ✴ Programming port available for PC connection allowing quick set-up ✴ Lockout protection guards against unauthorized setting changes ✴ Bumpless transfer allows continued temperature control if sensor fails ✴ Universal input, field configurable (Type J T/C default, PT100, mA, V) with high accuracy 18-bit D-A ✴ Short panel depth required Agency Approvals: Output 1 BOX 3 1 = Relay: 2A / 240 VAC 2 = Pulse DC for SSR drive: 5 VDC (30 mA max) 3 = Isolated 4-20mA / 0-20 mA 4 = Isolated 1-5V / 0-5V/0-10VDC 6 = Triac-SSR output 1A / 240 VAC C = Pulse DC for SSR drive: 14 VDC (40 mA max) 9 = Other Output 2 BOX 4 0 = None 1 = Relay: 2A / 240 VAC 2 = Pulse DC for SSR drive — 5 VDC (30 mA max) 3 = Isolated 4-20mA / 0-20 mA 4 = Isolated 1-5V / 0-5V/0-10V 6 = Triac-SSR output 1A / 240 VAC 7 = Isolated 20V @ 25 mA DC, Output Power Supply 8 = Isolated 12V @ 40 mA DC, Output Power Supply A = Isolated 5V @ 80 mA DC, Output Power Supply C = Pulsed voltage to drive SSR, 14V/40mA 9 = Other Signal Input — Universal, can be programmed in the field BOX 2 1 = Universal input (factory default = TC type J) Thermocouple: J, K, T, E, B, R, S, N, L, C, P RTD: PT100 DIN, PT100 JIS (0 to 60mV) 5 = Voltage: 0-10V, 0-5V, 1-5V, 0-1V 6 = DC Current: 0-20 mA (default), 4-20 mA 9 = Other Power Input BOX 1 4 = 90-250 VAC, 50-60 Hz 5 = 11-26 VAC / VDC Output 4 BOX 6 (TEC-4500 only) 0 = None 1 = Relay: 2A / 240 VAC 2 = Pulse DC for SSR drive — 5 VDC (30 mA max) 3 = Retransmission 4-20mA (default), 0-20 mA 4 = Retransmission 1-5 VDC (default)/ 0-5VDC, 0-10 VDC 6 = Triac-SSR output 1A / 240 VAC 7 = Isolated 20V @ 25 mA DC, Output Power Supply 8 = Isolated 12V @ 40 mA DC, Output Power Supply A = Isolated 5V @ 80 mA DC, Output Power Supply C = Pulsed voltage to drive SSR, 14V/40mA 9 = Other Output 3 BOX 5 0 = None 1 = Relay: 2A / 240 VAC 2 = Pulse DC for SSR drive — 5 VDC (30 mA max) 6 = Triac-SSR output 1A / 240 VAC 7 = Isolated 20V @ 25 mA DC, Output Power Supply 8 = Isolated 12V @ 40 mA DC, Output Power Supply A = Isolated 5V @ 80 mA DC, Output Power Supply C = Pulsed voltage to drive SSR, 14V/40mA 9 = Other 1 2 6 3 4 5 7 8 1 2 6 0 3 4 5 7 8 Configurable for 4 Programmable Outputs Configurable for 5 Programmable Outputs Hardware Code: TEC-4500- A Part Number based on the hardware code and any software pre-programming will be issued at time of order. Hardware Code: TEC-9500- Note: Detailed information on features common to digital microprocessor-based TEC temperature controls and the complete Table of Input Range and Accuracy can be found on page 13-46. File #: E244198
