Temperature Controllers www.tempco.com | (800) 323-6859 | email: [email protected] 13-9 Power Input Standard: 90-250 VAC, 47-63 Hz; 10 VA, 5W max. Optional: 11-40 VDC / 20 to 28 VAC, 47-63 Hz; 10 VA, 5W max. Signal Input Resolution: 18 bits Sampling Rate: 5 Times / Second (200msec) Maximum Rating: -2VDC minimum, 12VDC maximum Sensor Break Detection: Sensor open for Thermocouple and RTD inputs, sensor short for RTD input , below 1mA for 4-20mA input, below 0.25V for 1-5V input, not available for other inputs Sensor Break Response Time: Within 4 seconds for Thermocouple and RTD inputs, 0.1 second for 4-20mA and 1-5V inputs Event Input Number of Event Inputs: 2 Logic Low: -10V minimum, 0.8V maximum Logic High: 2V minimum, 10V maximum CT Input CT Type: TEC99998 Accuracy: ±2% of Full Scale Reading, ± 1 digit maximum Input Impedance: 294Ω Measurement Range: 0-50A AC Output of CT: 0-5V DC CT Mounting: Wall (Screw) Mount Sampling Rate: 1 Time/Second Output 1 / Output 2 Relay Rating: 2A,240V AC, 200000 Life Cycles for Resistive Load Pulsed Voltage: Source Voltage 5V, Current Limiting Resistance 66Ω Linear Output Resolution: 15 Bits Isolation Breakdown Voltage: 1000 V AC Load Capacity of Linear Output: Linear Current: 500Ω maximum, Linear Voltage: 10KΩ minimum Alarm Maximum Rating: 2A, 240VAC, 200000 Life cycles for resistive load Alarm Functions: Dwell Timer, Deviation Low, Deviation High, Deviation Band Low, Deviation Band High, Process High, Process Low Alarm Mode: Latching, Hold, Normal, Latching/Hold Dwell Timer: 0.1 to 4553.6 Minutes Data Communications Interface: RS-485 Protocol: Modbus RTU Address: 1-247 Baud Rate: 2.8 - 115.2 Kbits/sec Parity Bit: None, Even or Odd Stop Bit: 1 or 2 Bits Data Length: 7 or 8 Bits Communication Buffer: 160 bytes Analog Retransmission Output Signal: 4-20 mA, 0-20 mA, 0-10V Resolution: 15 Bits Accuracy: ±0.05% of span ± 0.0025% / °C Load Resistance: 0-500Ω for current output, 10KΩ minimum for voltage output Isolation Breakdown: 1000VAC minimum Integral Linearity Error: ±0.005% of span Linear Output Ranges: 0-22.2mA (0-20mA / 4-20mA), 0-5.55V (0-5V, 1-5V), 0-11.1V (0-10V) User Interface Keypad: 4 Keys Display Type: 4 digit LCD display No. of Display: 2 Upper Display Size: 0.58" (15mm) Lower Display Size: 0.3" (7.8mm) Programming Port Interface: Micro USB PC Communication Function: Automatic Setup, Calibration and Firmware Upgrade Control Mode Output 1: Reverse (Heating) or Direct (Cooling) Action Output 2: PID cooling control, Cooling P band 50~300% of PB, Dead band -36.0 ~ 36.0 % of PB ON-OFF: 0.1-90.0 (°F) hysteresis control (P band = 0) P or PD: 0-100.0 % offset adjustment PID: Fuzzy logic modified Proportional band 0.1 ~ 900.0°F, Integral time 0–3600 seconds, Derivative time 0-360.0 seconds Cycle Time: 0.1-90.0 seconds Manual Control: Heat (MV1) and Cool (MV2) Failure Mode: Auto transfer to manual mode while sensor break or A-D Converter damage Ramping Control: 0 to 900.0°F / Minute or 0 to 900.0°F / Hour Ramp Rate Environmental and Physical Specifications Operating Temperature: -10°C to 50°C Storage Temperature: -40°C to 60°C Humidity: 0 to 90 % RH (Non-Condensing) Insulation Resistance: 20MΩ minimum (@500V DC) Dielectric Strength: 2000V AC, 50/60 Hz for 1 Minute Vibration Resistance: 10 to 55 Hz, 10m/s2 for 2 Hours Shock Resistance: 200 m / s2 (20g) Moldings: Flame retardant polycarbonate Mounting: Panel Dimensions H×W×D: 1-7/8 × 1-7/8 × 2-3/8" (48 × 48 × 59 mm) Depth Behind Panel: 2" (50 mm) Cut Out Dimensions: 1-25/32 × 1-25/32" (45 × 45 mm) Weight: 6 oz (160 g) IP50 for the front panel, IP20 for rear terminals and housing. All indoor use. Rear Terminal Connections Stock and Common Part Numbers (All Stock Part Numbers Include Terminal Covers) (Default Type "J" Thermocouple Input) Part Output Out 2/ Option Number 1 Alm 1 1 TEC19001 Relay None None TEC19002 Relay Relay None TEC19003 Relay Relay Relay TEC19004 Pulse DC None None TEC19005 Pulse DC Relay None TEC19006 Pulse DC Relay Relay TEC19007 4-20mA None None TEC19008 4-20mA Relay Relay
